English English
Products
Home > Products > 1kv Cable Termination Kit

1kv Cable Termination Kit Manufacturers

Assume full responsibility to satisfy all needs of our clients; achieve continual advancements by endorsing the expansion of our purchasers; turn into the final permanent cooperative partner of clientele and maximize the interests of clients for 1kv Cable Termination Kit,1KV Heat Shrinkable Indoor and Outdoor Cable,Heat Shrink Cable Termination Kits,Heat shrink mini-terminations for cables,24kv Heat Termination Kit, Customers' profit and pleasure are constantly our biggest goal. You should contact us. Give us a probability, offer you a surprise.
1kv Cable Termination Kit, During the development, our company has built a well-known brand. It is well highly acclaimed by our customers. OEM and ODM are accepted. We've been looking forward to customers from all over the world to join us to a wild cooperation.

Related Products

Hot Products

  • 1kV Cold Shrinkable Two Cores Straight Through Joint kits

    1kV Cold Shrinkable Two Cores Straight Through Joint kits

    The installation of 1kV Cold Shrinkable Two Cores Straight Through Joint kits installation procedures from one end to the other side of the construction, the construction process cannot be changed, the process is very difficult to have a bubble will appear in the cable pipe, therefore the construction quality is higher, the construction of hot shrinkage is different, heat from one end to the other side, it is easy to result in uneven heating, which leads to the generation of air bubbles, seriously affect the construction quality.
  • 1kV Cold Shrinkable Two Cores Termination Kit

    1kV Cold Shrinkable Two Cores Termination Kit

    The installation of 1kV Cold Shrinkable Two Cores Termination Kit installation procedures from one end to the other side of the construction, the construction process cannot be changed, the process is very difficult to have a bubble will appear in the cable pipe, therefore the construction quality is higher, the construction of hot shrinkage is different, heat from one end to the other side, it is easy to result in uneven heating, which leads to the generation of air bubbles, seriously affect the construction quality.
  • 10kV and 24kV Elbow Type Cable Connector

    10kV and 24kV Elbow Type Cable Connector

    10kV and 24kV Elbow Type Cable Connector is used to provide power for electric operation mechanism ,or fully insulation,fully shield ,fully sealing for the high voltage side of the mutual inductor JDZ12A-10R. It is suitable for 15kV 35~50mm2 XLPE. The 10kV and 24kV Elbow Type Cable Connector test point can install live display to check the live status of the equipment and meet the requirements of the nuclear phase of the line. It can be operated with live, but cannot cut off short circuit current. It’s suitable for XLPE cable with sectional area 35mm2~150mm2.
  • 15kV Extended Bushing Holder

    15kV Extended Bushing Holder

    15kV Extended Bushing Holder or 15kV 250A bushing holder provides the interface for the 250A cable connector and mostly used on the oil-insulated (R-temp, hydrocarbon, or silicon) apparatus, including switch gear, transformer and capacitors. The bushing holder is molded using high quality epoxy rubber, which meet the requirement of standard EN50180/EN50181 DIN47636/HN52-S-61.
  • Access Control Composite Cable Termination

    Access Control Composite Cable Termination

    The external insulation of the Access Control Composite Cable Termination is composed of a glass fiber reinforced epoxy resin tube and a silicone rubber rainshed, aluminum alloy flanges with strong corrosion resistance are installed at both ends. Compared with the traditional porcelain tubing, the composite tubing has many advantages, It is the best substitute for porcelain covers and has gradually been accepted all over the world.
  • 12kV Integrated Bushing

    12kV Integrated Bushing

    The 12kV integrated bushing provides interface for 630A European-style joint products, which is mainly used for SF6 load switch branch box to connect with European-style front and rear joint and other products. The body of the product is made of high quality epoxy resin. Our independent plant covers an area of more than 14,000 square meters of production and testing equipment are complete.
  • Related Blog
  • Reviews

Send Inquiry